New Mexico HVAC License: Requirements, Exam and How to Apply, New Mexico HVAC License, New Mexico, Heat, Vent and Air Conditioning, Heat, Cooling and Process Pipe, Combined Mechanical, Retake policy, New Mexico Regulation and Licensing Department, how to get a New Mexico HVAC License, New Mexico HVAC License requirements, New Mexico HVAC License exam, New Mexico licensing board, New Mexico contractor license, license application steps, exam reference books, Experience, Business & Law exam, Required, Trade exam, Qualifying Party, Approval required, None

Home Licenses HVAC License New Mexico

HVAC License · MM-3, MM-4 & MM-98

New Mexico HVAC License: Requirements, Exam and How to Apply

In New Mexico, HVAC work is licensed through the mechanical (MM) classifications. Here you’ll find the MM-3, MM-4 and MM-98: the work each one allows, the experience it takes, the PSI exams and the application steps.

Last updated October 27, 2026 from New Mexico Regulation and Licensing Department requirements

Exam time

~6 hrs

MM-3 runs 245 min; Business & Law runs 130 min

Time to get license

~4 yrs

Experience of 4 years / 8,000 hours

Continuing ed

16 hrs

Applies to MM-3, MM-4 and MM-98

Do you need a New Mexico HVAC license?

It is. New Mexico puts the installation, alteration, repair and service of HVAC and process piping systems under its mechanical classifications. Air handling and refrigeration work takes the MM-3, hydronic and process piping takes the MM-4, and the MM-98 covers every kind of mechanical work.

You need the license when

  • Your work involves installing, altering, repairing or servicing HVAC air handling or refrigeration equipment, piping or ductwork (MM-3)
  • You handle boilers, chillers, cooling towers, or hydronic heating, cooling or process piping (MM-4)
  • You put in packaged units, condensing units, evaporative coolers or solar energy systems
  • You plan to bid and contract for every type of mechanical work from MM-1 through MM-4 (MM-98)

Exceptions

  • Controls and control wiring up to 24 volts are already part of the MM-3 and MM-4
  • With an MM-3, you can connect water to existing valved outlets
  • With an MM-3, you can bid incidental electrical, painting or structural work, provided a properly licensed contractor does it

What happens if you work unlicensed

We couldn’t confirm specific penalty amounts. As a rule, the New Mexico Regulation and Licensing Department can discipline anyone who contracts without the proper license, so wait until your license is issued before you bid or begin work.

How to get a New Mexico HVAC license in 6 steps

  1. Pick your classification Before you start
    Go with MM-3 for air handling and refrigeration or MM-4 for hydronic and process piping. If you want every mechanical class, aim for the MM-98.
  2. Document your experience Before you apply
    Build 4 years (8,000 hours) of experience in the trade.
  3. Get exam pre-approval Through PSI
    Start by getting pre-approved. PSI approves you to test at 407-264-0562.
  4. Pass your exams Exam day
    Book Business & Law and your trade exam through PSI online or at 855-807-3994. Testing centers are in the larger cities. You can use books, and the trade exam takes 75% to pass.
  5. Get approved as a Qualifying Party After you pass
    Your pass information comes by email. If you’re applying for the MM-3 or MM-4, you must be approved as a Qualifying Party.
  6. Submit your license application
    You can apply online through the state’s license application page. If you’d rather mail it, send the completed form with your documents and license fee to the address it lists.

New Mexico HVAC application checklist

Everything for the New Mexico application on one page

  • Documented experience of 4 years / 8,000 hours
  • PSI exam pre-approval
  • A passing Business & Law score
  • A passing MM-3 or MM-4 trade exam score (75%)
  • Qualifying Party approval
  • Completed application, documents and the license fee

New Mexico HVAC license classes

HVAC work in New Mexico falls into two mechanical classes, and a combined license covers all of it. Each class also requires you to pass Business & Law.

MM-3 Most common

Heat, Vent and Air Conditioning

This is the class for air handling and refrigeration. It takes in equipment and piping like coils, fans, packaged and condensing units, plus evaporative coolers, ductwork, solar energy systems and pneumatic tube systems.

ExamB&L + MM-3
LimitNot stated

MM-4 Hydronic & process

Heat, Cooling and Process Pipe

This is the class for hydronic heating, cooling and process piping. Think boilers, chillers, chilled water, steam and hot water systems, pressure vessels, cooling towers and fuel oil piping.

ExamB&L + MM-4
LimitNot stated

MM-98 All mechanical

Combined Mechanical

Includes every type of work from MM-1 through MM-4, along with MS-3, MS-6, MS-12 and MS-14. You need to hold MM-1 through MM-4 before you can get it.

ExamB&L + MM-1 to MM-4
LimitNot stated

Requirements for each New Mexico HVAC class

Every class asks for the same experience. The trade exam is what differs, and the MM-98 requires all four mechanical classes.

RequirementMM-3MM-4MM-98
Experience4 years / 8,000 hours4 years / 8,000 hours4 years / 8,000 hours
Business & Law examRequiredRequiredRequired
Trade examMM-3 (100 questions)MM-4 (90 questions)MM-1, MM-2, MM-3 and MM-4
Qualifying PartyApproval requiredApproval requiredNot stated
Other licenses heldNoneNoneMM-1 through MM-4
Continuing education16 hours16 hours16 hours

The New Mexico HVAC exam

The MM-3 and MM-4 each take two exams: Business & Law and the trade exam. For the MM-98 you take five: Business & Law and MM-1 through MM-4. You can use books on all of them, and you may tab and highlight the approved references.

Format

Open book

Questions

100 (MM-3) / 90 (MM-4) + 50

Passing score

75%

Exam vendor

PSI

Scoring & content

  • MM-3 has 100 questions and a 245-minute limit. Topics: refrigerants; piping; heating and cooling equipment; motors, controls and low voltage wiring; duct work, ventilation and exhaust
  • MM-4 has 90 questions and a 235-minute limit. Topics: process piping; steam and hot water boiler systems; controls; fire suppression; combustion air and venting
  • Business & Law: 50 questions in 130 minutes
  • Among the references are the New Mexico Mechanical Code (Title 14) and the 2021 Uniform Mechanical Code
  • For MM-4, the New Mexico Boiler Rules (NMAC 14.9.4) are on the reference list too

Retake policy

  • We couldn’t confirm the retake rules
  • To retest or reschedule, call PSI at 855-807-3994
  • MM-3, MM-4 and Business & Law are $68.88 each, whether it’s your first try or a retake

Books and codes for this exam (open book)

New Mexico’s MM-3, MM-4 and Business and Law exams are open book: the references below can be tabbed, highlighted and used during the test. Books marked study only are listed for the MM-4 trade but aren’t allowed in the room.

ReferenceEditionHow it’s used
Uniform Mechanical Code (UMC) — MM-3 and MM-4 exams2021Allowed in exam
Modern Refrigeration and Air Conditioning — MM-3 and MM-4 exams22nd editionAllowed in exam
IPT Pipe Trades Handbook — MM-3 and MM-4 examsNot statedAllowed in exam
New Mexico Mechanical Code (NMAC Title 14, Chapter 9) — MM-3 and MM-4 examsNot statedAllowed in exam
ACCA Duct Calculation Slide Rule — MM-3 examNot statedAllowed in exam
SMACNA HVAC Duct Construction Standards: Metal and Flexible — MM-3 exam4th editionAllowed in exam
Sheet Metal — MM-3 examNot statedAllowed in exam
NFPA 13: Standard for the Installation of Sprinkler Systems — MM-4 exam2007Allowed in exam
NFPA 17: Standard for Dry Chemical Extinguishing Systems — MM-4 examNot statedAllowed in exam
New Mexico Boiler Rules and Regulations (NMAC 14.9.4) — MM-4 exam2005Allowed in exam
New Mexico Plumbing Code (NMAC Title 14, Chapter 8) — MM-42015Study only
Uniform Plumbing Code (UPC) — MM-42021Study only
Low Pressure Boilers — MM-4Not statedStudy only
NFPA 31: Standard for the Installation of Oil-Burning Equipment — MM-42020Study only
NASCLA Contractor’s Guide to Business, Law and Project Management, Basic Edition — Business and Law examBasic EditionAllowed in exam

MM-98 Combined Mechanical candidates take the MM-1 Plumbing and MM-2 Natural Gas Fitting exams as well, which use the plumbing and gas fitting reference lists.

Prep for the New Mexico HVAC exam

Our exam prep course, Total Prep and complete bundle for the New Mexico HVAC exam. Prices are coming soon.

Books for this exam

Renewing your New Mexico HVAC license

The MM-3, MM-4 and MM-98 all require 16 hours of continuing education in New Mexico. Contractor licenses last three years, and renewing costs the same classification fee you paid to get licensed: $150 for the MM-3 or MM-4 and $300 for the MM-98. If you’re late, you pay $1 a day for the first 30 days, then the equivalent of a full year’s fee from 30 to 90 days. Past 90 days, the license is cancelled.

Renewal cycle

3 years

CE hours

16

Renewal fee

$150 ($300 MM-98)

Late penalty

$1/day (1–30 days)

New Mexico HVAC CE

Hours, deadlines, required topics and the renewal steps, in one guide.

Licensed in another state?

In New Mexico, reciprocity agreements apply only to Journeyman licenses. We couldn’t confirm any reciprocity for the MM-3, MM-4 or MM-98 contractor classes.

Journeyman licenses: reciprocity with 11 states

Journeyman licenses from these states are covered: Wyoming, Utah, Texas, South Dakota, Oklahoma, Nebraska, Montana, Idaho, Colorado, Arkansas and Alaska.

MM contractor classes: no agreement listed

You’ll apply as a new applicant and take both Business & Law and your trade exam.

City and county rules in New Mexico

The state issues MM licenses. We couldn’t confirm any city or county licensing rules, so check with your local office before pulling permits.

State handles

  • MM-3, MM-4 and MM-98 licenses
  • Qualifying Party approval
  • Exams, through PSI
  • Continuing education requirements

What cities & counties handle

  • Building and mechanical permits, plus inspections
  • Local business licenses, if required

Who oversees New Mexico HVAC contractors

Licensing authority

New Mexico Regulation and Licensing Department

505-476-4500

rld.nm.gov, Apply for a Construction Industries license

What the board does

  • Issues the MM-3, MM-4, MM-98 and other mechanical classifications
  • Approves Qualifying Parties
  • Sets the continuing education rules
  • Takes license applications online

New Mexico HVAC license: common questions

Which license do you need for HVAC work in New Mexico?

The MM-3 covers air handling, ductwork and refrigeration. The MM-4 is for hydronic, boiler and process piping work, and the MM-98 includes every mechanical class.

How much experience does a New Mexico HVAC license require?

The MM-3, MM-4 and MM-98 each require 4 years (8,000 hours) of experience.

Can you use books on the New Mexico HVAC license exam?

Yes. PSI’s exams are open book, and you can tab and highlight the approved references. The MM-3 and MM-4 exams take 75% to pass.

How many questions are on the New Mexico MM-3 HVAC exam?

It has 100 questions and a 245-minute limit. You also sit for Business & Law, which has 50 questions and a 130-minute limit.

How do you get the New Mexico MM-98 mechanical license?

You need 4 years of experience and must already hold MM-1 through MM-4. In practice, that’s five exams: Business & Law and the four mechanical classes.

Will New Mexico accept my out-of-state HVAC license?

Reciprocity applies only to Journeyman licenses, with Alaska, Arkansas, Colorado, Idaho, Montana, Nebraska, Oklahoma, South Dakota, Texas, Utah and Wyoming. We couldn’t confirm any for the MM contractor classes.

Do New Mexico HVAC licenses require continuing education?

Yes. These licenses need 16 hours of continuing education in New Mexico.

Where this information comes from

  1. New Mexico Regulation and Licensing Department, Apply for a Construction Industries license
  2. PSI, New Mexico exam catalog
  3. New Mexico Mechanical Code, 14.9.2 NMAC (PDF)
  4. New Mexico Mechanical Code, Title 14 (State Records Center)
  5. New Mexico Boiler Rules and Regulations, 14.9.4 NMAC
  6. PSI, New Mexico licensing fees (PDF)
  7. PSI, New Mexico contractor examinations candidate information bulletin (PDF)
  8. PSI, NM CID contractor license application (PDF)
  9. PSI, NM CID Qualifying Party certificate application (PDF)

Last updated October 27, 2026. Spot something out of date? Tell us.

Linden Prep is an independent exam prep and continuing education company. It is not affiliated with the New Mexico Regulation and Licensing Department.